Electrician · Milton

Licensed electricians serving Milton

Panel upgrades, rewires, pot lights and EV chargers. Daybot Solutions Inc. will pull the ESA permit, meet the inspector, and leave the breaker panel properly labelled.

  • Typical response: same day where we can
  • Serving Milton
ECRA/ESA licensedPermit & inspection includedFully insuredUpfront pricing
Services

The work we take on

Typical responseSame day where we can

  1. 01

    Panel upgrades

    Swap a tired 60 or 100 amp panel for a 200 amp service so the house can carry a heat pump, an EV charger and a finished basement without nuisance trips.

    Signature
  2. 02

    Knob-and-tube & aluminum rewiring

    Replace the old wiring insurers refuse to cover, one circuit or one storey at a time, with as few holes in your plaster as the job allows.

    Signature
  3. 03

    EV charger installation

    Level 2 charger mounted, load calculation done and the circuit run to the garage or driveway, permitted and inspected.

    Signature
  4. 04

    Pot light retrofits

    Dimmable LED pot lights cut into existing ceilings on a proper switched circuit, laid out so the room lights evenly instead of in hot spots.

  5. 05

    Troubleshooting & dead circuits

    Half the outlets out, a breaker that keeps tripping, lights that flicker — we trace it to the actual fault instead of replacing parts and hoping.

  6. 06

    Standby generators & transfer switches

    Portable inlet or automatic standby generator wired through a proper transfer switch so you never backfeed the grid during an outage.

  7. 07

    Service mast & meter base repair

    Storm-damaged or pulled-away service masts re-secured and resealed, coordinated with the utility so power is off for hours, not days.

  8. 08

    Smoke, CO & GFCI safety upgrades

    Interconnected smoke and CO alarms, GFCI protection in kitchens, baths and outdoors, and AFCI breakers on bedroom circuits.

Blaze Potter

The workshop

About Daybot Solutions Inc.

Daybot Solutions Inc. started with one van, a licence, and a habit of answering the phone. Since then the work has been the same: do it to code, explain it in plain language, and leave the place cleaner than we found it. Every job is permitted through the ESA, every panel gets labelled properly, and nothing gets buried behind drywall that we would not want an inspector to see.

Fast, affordable electrical work, with someone always available.

Response
Same day where we can
Assurance

Credentials & cover

ECRA/ESA Licensed Electrical Contractor

Registered with the Electrical Safety Authority — licence number on every quote.

Master Electrician

Certified Master Electrician on staff and responsible for every job we take.

Red Seal 309A Electrician

Construction & maintenance electrician, Certificate of Qualification held.

$5M liability insurance

Certificate of insurance available on request before work starts.

WSIB coverage in good standing

Clearance certificate provided so you carry no liability for our crew.

ESA permit on every job

We file the notification and hand you the Certificate of Acceptance.

Where we work

Service area

Typical response: Same day where we can.

Milton

Appointments

Reserve a visit

Pick a day and time. It takes about a minute.

Book a visit

Pick a time that works. Takes about 30 seconds.

August 2026
SMTWTFS
Questions

Before you book

Anything else, ask us directly on (416) 347-3761.

The usual signs are a 60 or 100 amp service on the label, a fuse box instead of breakers, no room left for new breakers, or a breaker that trips whenever two big appliances run at once. If you are adding an EV charger, a heat pump, a hot tub or a basement suite, we do a load calculation first — sometimes the existing service is fine and you only need a subpanel.

Almost all electrical work in Ontario needs an ESA notification, and only a licensed contractor can file one. We pull it, meet the inspector, and give you the Certificate of Acceptance. Keep that certificate — insurers and buyers' lawyers ask for it, and unpermitted work is the most common thing that stalls a house sale.

For knob-and-tube, most insurers want it fully removed from the living space. For aluminum branch wiring, many will accept a certified pigtailing remediation at every device instead of a full rewire, which costs a fraction of the price. We inspect first, tell you which route your insurer will actually accept, and put it in writing.

A panel upgrade is a one day job for most homes, with the power off for roughly four to six hours in the middle of it. Rewires are done circuit by circuit so you keep power to the rest of the house overnight. We tell you the shutdown window the day before so you can plan around the fridge and anyone working from home.

Access, mostly. A basement with an open ceiling costs far less to run circuits through than a finished second floor with plaster walls. After that it is distance from the panel, whether the service itself needs upgrading, and how much drywall repair is involved. We quote a fixed price after seeing it, not a rate per hour that grows.

Yes — our workmanship is warrantied, and manufacturer warranty on the equipment is passed straight through to you. If something we installed misbehaves, we come back and make it right.

Get in touch

Let’s talk about your job

(416) 347-3761chocalatechocalate58@gmail.com
Based in

Milton

Opening hours
MondayToday
7 am – 5 pm
Tuesday
7 am – 5 pm
Wednesday
7 am – 5 pm
Thursday
7 am – 5 pm
Friday
7 am – 5 pm
Saturday
8 am – 1 pm
Sunday
Closed

24/7 emergency service — call anytime

Request a quote

Tell us what you need and we’ll come straight back to you. Typical response: same day where we can.

A photo of the problem saves a trip. Optional.