01
Progressive dies
Build and debug stations for feeding, piercing, forming and cutoff with strip progression documented.
Est. 2005 · Licence 7A-11531
Tool and die work built around the job, not a guess.
Qualified tool and die makers serving Milton, with the scope, safety plan and schedule written down before work starts.
- Red Seal 430A Tool and Die Maker
- Fully insured
- 21 years in business
- Same day where we can
Serving Milton
- LicensedLicence 7A-11531
- Response timeSame day where we can
- Experience21 years in the trade
Gauge Tool & Die
Welcome
Welcome to Gauge Tool & Die
Tool & Die Maker in Milton
Looking after Milton and the surrounding area since 2005.
Est. 2005Who we are
About Gauge Tool & Die
Gauge Tool & Die provides tool and die work for stampers, moulders, machine shops and production manufacturers. We plan the access and safety requirements first, keep the person approving the work informed, and hand over the records the job calls for when it is done.
What we do
- Progressive dies
- Die repair and maintenance
- Jigs and fixtures
- Punches and form tools
- Tryout and troubleshooting
- Engineering changes
What we offer
Our services
Work we take on for homes and businesses in Milton and nearby.
- 02
Die repair and maintenance
Correct wear, galling, chipped details and alignment before they become scrap across a full run.
- 03
Jigs and fixtures
Design and build repeatable workholding for machining, welding, inspection and assembly.
- 04
Punches and form tools
Machine, heat-treat and fit punches, buttons, pads and form details to the approved drawing.
- 05
Tryout and troubleshooting
Run the tool, read the part and correct feed, timing, shut height and forming conditions at the press.
- 06
Engineering changes
Modify existing tooling to a controlled revision while protecting every unaffected feature.
For your peace of mind
Licences & certifications
Ask any contractor to show you these before work starts. Ours are set out in full below.
- Service area
- Milton
- Response time
- Same day where we can
- Red Seal 430A Tool and Die Maker
- Fully insuredCertificate of insurance available before work starts.
- WSIB coverage in good standingClearance certificate available for commercial and industrial sites.
- Site-specific safety planHazards, lockout requirements and access are reviewed before the crew mobilizes.
- Licence no.
- 7A-11531
- Established
- 2005
Ready when you are
Need a hand in Milton?
Speak to someone who does the work themselves. Typical response: Same day where we can.
Good questions
Frequently asked
Our regular work includes Progressive dies, Die repair and maintenance, Jigs and fixtures, along with the related inspection, setup and repair needed to leave the job ready for service. Send the equipment, drawing or site details and we will tell you plainly whether it fits our scope.
Red Seal 430A Tool and Die Maker is the trade-specific qualification we lead with. Insurance and WSIB documents are available before the job, and any permit, engineered drawing or manufacturer procedure the work requires is identified in the quote.
We quote from the actual scope: drawings and measurements where they exist, equipment model and condition where they do not, access, shutdown time, materials and testing. Changes are written down before they become extras.
Yes. For stampers, moulders, machine shops and production manufacturers, we plan access, lockout or isolation, lifts and hot-work controls before arrival. If the work needs a shutdown, the quote separates preparation from the outage window so the interruption stays as short as practical.
A few wide photos, the address, the make and model of any equipment, the drawing or part file if there is one, and the date the work has to be ready. That is usually enough to assign the right person and avoid a wasted trip.
Where we work
Service area
Not sure whether you are inside it? Give us a call — we will tell you straight.
- Milton
Book a visit
Pick a time that suits you
Choose a day, leave your number, and we will be in touch to confirm.
- Takes half a minute — no account needed.
- We confirm by phone or text before we set off.
Rather talk it through?
(905) 555-0137Book a visit
Pick a time that works. Takes about 30 seconds.
October 2026
SMTWTFS
Get in touch
Request a quote
Leave a few details and we will come back to you. Typical response: Same day where we can.
Tell us about the job
Name and number is plenty — anything else helps us come prepared.
Contact details
- (905) 555-0137
- Milton
Opening hours
- Monday
- 7 am – 5 pm
- Tuesday
- 7 am – 5 pm
- Wednesday
- 7 am – 5 pm
- Thursday
- 7 am – 5 pm
- FridayToday
- 7 am – 5 pm
- Saturday
- 8 am – 1 pm
- Sunday
- Closed