Welder · Milton
Mobile welding & fabrication in Milton
Railings, gates, structural steel and on-site repairs, CWB certified. Ferrous Welding will bring the shop to you and quote the job before striking an arc.
Serving Milton
- CWB certified
- Mobile — we come to you
- Aluminum & stainless
- LicensedLicence 7A-80290
- Response timeSame day where we can
- Serving Milton since 2010
About us
About Ferrous Welding
16Years of experience
Ferrous Welding welds to code and cleans up after itself, which in this trade is half the battle. Mobile for anything that cannot move, shop work for what can, CWB certification for the jobs that legally require it, and a fire watch on every hot work job. Send a photo of what broke — we will tell you straight whether it is worth repairing.
What we do
Welding & fabrication services in Milton
Railings, gates, structural steel and on-site repairs, CWB certified. Ferrous Welding will bring the shop to you and quote the job before striking an arc.
Mobile on-site welding
Fully equipped truck brought to your property, farm or job site for repairs that cannot be carried into a shop.
Structural steel & beams
Beams, columns and lintels fabricated and welded to engineered drawings, with the weld procedure documented for the inspector.
Railings, guards & stair stringers
Interior and exterior railings built to Building Code height and spacing, from plain steel to forged detail.
Gates, fences & security bars
Driveway gates, side gates and window guards fabricated to your opening, hinged so they still swing true in five years.
Aluminum & stainless TIG work
Boat, trailer and food-grade stainless work TIG welded clean, where a mild-steel repair would just fail again.
Trailer & equipment repair
Cracked frames, broken hitches, ramps, decks and axles repaired properly rather than built up with filler passes.
Farm & industrial repair
Buckets, augers, hoppers, guards and hard-facing repaired on site so equipment gets back to work the same day.
Custom fabrication
Brackets, frames, fire pits, stair stringers, shelving and one-off pieces built from a sketch or a measurement.
Looking for help in Milton?
Same day where we can response on new enquiries.
Credentials
Licences & certifications
The paperwork behind the work at Ferrous Welding.
- CWB certified welderCanadian Welding Bureau welder qualification, current and testable.
- CSA W47.1 certified fabricatorDivision certification for structural steel welding — required for most engineered work.
- Red Seal WelderCertificate of Qualification in welding with Red Seal endorsement.
- Welds to CSA W59Structural welding to code, with procedures documented for engineers and inspectors.
- Hot work permit & fire watchFire extinguishers, blankets and a post-work fire watch on every indoor or roof job.
- WSIB coverage & $2M liabilityCertificates supplied before we roll onto your site.
Questions
Frequently asked
If your question isn't here, call us — we would rather explain it than have you guess.
Both. Anything bolted down, too big to move, or attached to a building we do on site from the truck — that is most railings, gates, structural work and equipment repair. Small pieces are cheaper to bring to the shop, where we have the bigger machines and better setup. Send a photo and we will tell you which is the cheaper route.
Aluminum and stainless, yes — TIG, and we prep and clean properly, which is most of the job on aluminum. Cast iron is case by case: some castings can be repaired with nickel rod and controlled preheat and cooling, others will simply crack again beside the weld. We will tell you honestly whether a repair is worth attempting before charging you for it.
If it carries a load — a beam replacing a wall, a balcony, a mezzanine, anything a permit covers — yes, and the fabricator needs the matching certification. We work from your engineer's drawings or can point you to one. For non-structural work like a railing or a gate, no drawings are needed, just measurements.
Typically one to three weeks from final measurement: a day or two to fabricate, time for finishing, then install. Measurement has to happen after the stairs and landings are final, since we build to the actual opening rather than the plan. Rush work is possible and we will tell you the cost rather than quietly missing the date.
Yes. Mild steel outdoors needs protection or it will bleed rust stains down whatever it is bolted to — we prime and paint, or send pieces for powder coating or hot-dip galvanizing depending on the exposure. Galvanizing costs more up front and is the right call for anything exposed to road salt.
With proper precautions, yes, and we take them: combustibles cleared or blanketed, a fire extinguisher at the work, sparks contained, and a fire watch kept for a period after we stop. Most fires from hot work start after the welder leaves, which is exactly why the fire watch is not optional for us.
Service area
Where we work
Ferrous Welding covers these communities.
- Milton
Office hours
- Monday
- 7 am – 5 pm
- Tuesday
- 7 am – 5 pm
- Wednesday
- 7 am – 5 pm
- Thursday
- 7 am – 5 pm
- Friday
- 7 am – 5 pm
- SaturdayToday
- 8 am – 1 pm
- Sunday
- Closed
Book online
Pick a time that suits you
Choose a slot and we will confirm it. No account, no waiting on hold.
Book a visit
Pick a time that works. Takes about 30 seconds.
Contact
Request a quote
Tell us what you need and we will get back to you with a straight answer.
- Phone
- (905) 555-0124Same day where we can response
- Address
- Milton
Send us the details
Name and phone number are all we need to start.