Sheet Metal Worker · Milton
Custom sheet metal & ductwork in Milton
Ductwork, flashing, hoods and metal cladding formed to fit your building. Brightfold Sheet Metal will pattern from the old piece or measure the real angles, then make it properly.
Serving Milton
- Red Seal sheet metal
- Shop fabrication & site work
- Custom flashing formed on site
- LicensedLicence 7A-67512
- Response timeSame day where we can
- Serving Milton since 2000
About us
About Brightfold Sheet Metal
26Years of experience
Brightfold Sheet Metal can make the parts nobody stocks. Duct fittings sized for the equipment actually installed, chimney flashings bent to the real roof pitch, hood liners built for the hood you bought, and cladding that still looks flat five summers later. Bring us the broken piece or send a photo with a measurement, and we will make one that fits the first time.
What we do
Sheet metal services in Milton
Ductwork, flashing, hoods and metal cladding formed to fit your building. Brightfold Sheet Metal will pattern from the old piece or measure the real angles, then make it properly.
Custom ductwork & fittings
Trunks, take-offs, transitions and elbows fabricated to your actual space rather than forced together from stock parts that choke the airflow.
Range hood & make-up air
Kitchen hood liners and duct runs built for the hood you bought, vented outside on the shortest sensible route with the make-up air the code requires.
Custom flashing & drip edge
Chimney, wall, valley and window flashings brake-formed on site to the real angles, because a folded piece of stock flashing is where most leaks start.
Metal roofing & standing seam
Standing seam and metal panel roofs fabricated and installed, with the trims, closures and snow retention that make them last their full life.
Soffit, fascia & cladding
Aluminum and steel cladding, column wraps and architectural panels bent to fit and fastened so nothing oil-cans in the first heat wave.
Dryer, bath & HRV venting
Rigid metal vent runs for dryers, bath fans and HRVs, sealed and pitched properly so lint and condensate go outside instead of into a joist bay.
Stainless counters & splash backs
Commercial kitchen counters, shelves, hoods and splash backs fabricated in stainless with welded, ground and polished seams a health inspector will pass.
Balancing & airflow correction
Rooms that never heat or cool measured and fixed — undersized returns, crushed flex, missing dampers and runs that were never sized for the equipment.
Looking for help in Milton?
Same day where we can response on new enquiries.
Credentials
Licences & certifications
The paperwork behind the work at Brightfold Sheet Metal.
- Red Seal Sheet Metal Worker308A Certificate of Qualification with Interprovincial Red Seal endorsement.
- Ductwork sized to recognised design methodsResidential duct layouts sized from a heat loss and gain calculation, not copied from the old system.
- Sealed and supported to codeJoints sealed, hangers spaced and fire separations respected wherever duct crosses them.
- Working at Heights trainedCurrent working at heights certification for roof and cladding work.
- Own brake, shear and roll formingPieces made to your measurement in our shop or on the truck, not ordered and hoped for.
- WSIB coverage & $2M liabilityCertificates provided before work starts.
Questions
Frequently asked
If your question isn't here, call us — we would rather explain it than have you guess.
Nine times out of ten it is the ducts, not the furnace. The usual culprits are a run that is too long or too small, flex duct crushed behind a joist, a damper someone closed years ago, or not enough return air so the room cannot exhaust what you push into it. We measure airflow and temperatures at the register before recommending anything, because replacing equipment will not fix a duct problem.
Yes, and that is often the cheapest route. Bring the old flashing, cap, transition or panel and we will pattern from it and brake a new one, in steel, aluminum, copper or stainless. If it cannot come off the building, we take the measurements and angles on site and form it there.
For anything with real capacity, yes — and once a hood moves a large volume of air, the code also expects make-up air so the house is not depressurised, which can pull combustion gases back down a chimney. Recirculating hoods with charcoal filters are an option in condos and interior kitchens, but they manage smell rather than heat and grease.
A properly detailed metal roof outlives several shingle roofs and sheds snow, which matters on low-slope sections and over entryways. It costs considerably more up front and the details matter enormously — the panels rarely fail, the flashings and fasteners do. If you plan to sell in a few years, shingles are the rational choice.
Small fittings and flashings are usually same or next day. Full duct systems and metal roofing are quoted with a fabrication window because the pieces are made for your building. We give you the date after measuring, not before.
Service area
Where we work
Brightfold Sheet Metal covers these communities.
- Milton
Office hours
- Monday
- 7 am – 5 pm
- Tuesday
- 7 am – 5 pm
- Wednesday
- 7 am – 5 pm
- Thursday
- 7 am – 5 pm
- Friday
- 7 am – 5 pm
- SaturdayToday
- 8 am – 1 pm
- Sunday
- Closed
Book online
Pick a time that suits you
Choose a slot and we will confirm it. No account, no waiting on hold.
Book a visit
Pick a time that works. Takes about 30 seconds.
Contact
Request a quote
Tell us what you need and we will get back to you with a straight answer.
- Phone
- (905) 555-0157Same day where we can response
- Address
- Milton
Send us the details
Name and phone number are all we need to start.